The symbols example "Cisco network topology - Vector stencils library" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the Cisco Network Diagrams solution from the Computer and Networks area of ConceptDraw Solution Park. The logical topology in contrast, is the way that the signals act on the network media, or the way that the data passes through the network from one device to the next without regard to the physical interconnection of the devices." The physical topology of a network is determined by the capabilities of the network access devices and media, the level of control or fault tolerance desired, and the cost associated with cabling or telecommunications circuits. This refers to the layout of cabling, the locations of nodes, and the interconnections between the nodes and the cabling. The shape of the cabling layout used to link devices is called the physical topology of the network. "There are two basic categories of network topologies: The vector stencils library "Cisco network topology" contains 89 symbols of Cisco network devices and design elements for drawing computer network topology diagrams. The symbols example "Cisco switches and hubs - Vector stencils library" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the Cisco Network Diagrams solution from the Computer and Networks area of ConceptDraw Solution Park. Repeater hubs also participate in collision detection, forwarding a jam signal to all ports if it detects a collision." The device is a form of multiport repeater. A hub works at the physical layer (layer 1) of the OSI model. It is a very clean transparent background image and its resolution is 1280圆40, please mark the image source when quoting it. It has multiple input/ output (I/ O) ports, in which a signal introduced at the input of any port appears at the output of every port except the original incoming. Switch-23328 1280 - Cisco Switch Icon is a high-resolution transparent PNG image. "An Ethernet hub, active hub, network hub, repeater hub, multiport repeater or hub is a device for connecting multiple Ethernet devices together and making them act as a single network segment. This means that messages have to be transmitted out of every port of the hub, greatly degrading the efficiency of the network." Hubs neither provide security, or identification of connected devices. Because of these features, a switch is often considered more "intelligent" than a network hub. This maximises security and efficiency of the network.
CISCO SWITCH ICON MAC
Each networked device connected to a switch can be identified using a MAC address, allowing the switch to regulate the flow of traffic. Switches manage the flow of data across a network by only transmitting a received message to the device for which the message was intended. Multiple cables can be connected to a switch to enable networked devices to communicate with each other. "A switch is a device used on a computer network to physically connect devices together.
CISCO SWITCH ICON DOWNLOAD
If you have followed each step correctly you will get result like this otherwise repeat these steps until you have correct configuration.The vector stencils library "Cisco switches and hubs" contains 26 symbols of Cisco switches and hubs for drawing computer network diagrams. Download visio, program, stencil, networking, switch, Cisco icon, Category: Network & communications, Style: Flat, Packages: Cisco Networking, Author: Yudha Agung.
As we know that UpaaePC2 has the IP address of 192.168.1.3 so we will enter “ping 192.168.1.3” at the command prompt and wait for the result. Now click on UpaaePC1 and select command prompt. įor validating if our computer can communicate through switch we use ping, if pinging the other computer results in no packet loss then we are good and having a working network. You should also know that the IP addresses of the devices connected to the same switch should belong to the same subnet (network) otherwise communication will be unsuccessful.įor IP Configuration click on UpaaePC1, a new window will open with tabs/buttons at the top, click on “ Desktop” and select “ IP Configuration” from the new window as shown in Figure 8.Įnter 192.168.1.2 in the IP Address field and click on the subnet mask it will automatically populate with 255.255.255.0, close this window and repeat step 6 and step 7 for UpaaePC2 with this IP Address 192.168.1.3. A network switch cannot forward packets from the source to destination if it does not know the IP addresses of its connected devices.
On completing step 5 it’s time to configure IP Addresses for both PC’s. While the connection type being selected click on UpaaePC1 and then UpaaeSwitch1 ( Figure 7)and repeat this step for UpaaePC2. Now select the Flash Icon which is for connection from the bottom left menu and then click on the automatically select connection type icon( Figure 6).
0 kommentar(er)
